Schluter®-LIPROTEC-ECX

Controlador LED y atenuador

El LIPROTEC-ECX es una fuente de alimentación LED y un regulador de intensidad en la pared en un único dispositivo que elimina los problemas de compatibilidad entre los controladores y los reguladores de intensidad.
  • Regulación suave y uniforme
  • Rango de regulación: 5% a 100%
  • Puede controlar varios nichos KERDI-BOARD-SNLT (hasta 60 vatios)
  • Cabe en una caja de interruptores eléctrica estándar
  • Incluye tres placas frontales intercambiables para combinar con la mayoría de las decoraciones
  • Certificación UL en EE.UU. y Canadá
 ...leer más  ...mostrar menos

Tipo de producto

Seleccionar todas las opciones para encontrar el
producto específico que desea comprar.

Encuentre aquí los accesorios recomendados

Schluter®-LIPROTEC-ECX es una fuente de alimentación LED y un regulador de intensidad en la pared, en un único dispositivo. Ofrece una regulación suave y uniforme con un rango de regulación del 5% al 100%. LIPROTEC-ECX puede controlar varios nichos KERDI-BOARD-SNLT (de hasta 60 vatios). Además, incluye tres placas frontales intercambiables para combinar con la mayoría de las decoraciones.

LIPROTEC-ECX no requiere ningún mantenimiento especial.

¿Está listo para instalar su regulador de intensidad Schluter®-LIPROTEC-ECX? Consulte paso a paso las instrucciones de instalación o vea nuestro completo vídeo de instalación a continuación.

Q:

Do we need to use all three LIPROTEC components? Can I use another driver, LED, or wire?

A:

The LIPROTEC system is specifically designed to work together and is UL listed as a system. The cable and gland seal the wire outlet hole. The LED connectors are...

Leer más
Q:

Why is my LIPROTEC LED flashing?

A:

The driver is overloaded or overheated. Check the sum of wattage on the driver and make sure it is below the rated output (LIPROTEC-ECX: 60W or...

Leer más
Q:

What are the benefits of the LIPROTEC-ECX driver vs the LIPROTEC-ECD?

A:

LIPROTEC-ECX is an all-in-one solution with one connection point to run from the junction box directly to the LED.

Leer más
Q:

Can I run more than one LED to the LIPROTEC-ECX driver?

A:

Yes. The LED light is 1.7 watts and the LIPROTEC-ECX control is rated up to 60 watts. This means that you can run up to 30 niches on the LIPROTEC-ECD...

Leer más
Q:

Can the LIPROTEC-ECX integrate with my smart home?

A:

No, only the LIPROTEC-ECD driver can be used with smart dimmers.

Leer más
Q:

Do I need special wiring for the LIPROTEC-ECX?

A:

No, but the LIPROTEC-ECX needs to have the rough in wiring for high voltage (120V AC) on a particular end (the bottom) of the junction box, otherwise...

Leer más
Q:

Does the LIPROTEC-ECX need to be on its own circuit?

A:

No, the LIPROTEC system can be jumped off an existing lighting circuit if needed. Contact your local electrician for guidance and code compliance.

Leer más
Q:

Can the LIPROTEC-ECX be installed in a double gang box, along side an existing switch?

A:

Yes, but a voltage barrier or divider (not included) needs to be installed between the two switches. Contact your local electrician for guidance and...

Leer más
Q:

Can I pull power from my DITRA-HEAT or other floor heating circuit to power my LIPROTEC LED?

A:

No. Floor heating should be on a dedicated circuit. You also increase the risk of accidentally miswiring the lighting into a 240V circuit.

Leer más
Q:

Does the LIPROTEC-ECX need to be on a GFCI circuit?

A:

No. GFCIs are typically not used on a light circuit but this will not affect the performance of the LIPROTEC system.

Leer más
Q:

Can I connect the LIPROTEC-ECX to 240V power?

A:

No. This will damage the driver and void the warranty. The driver is rated for single-phase 110VAC-120VAC power.

Leer más
Q:

What would happen to the LIPROTEC system in case of a power surge or brownout?

A:

Both Schluter drivers have built-in protection against power fluctuations and will shut down in either of the situations listed above.

Leer más
Q:

What if my LIPROTEC LED turns on but doesn't dim?

A:

The slider is misaligned. Remove the faceplate on the ECX. Slide the black dimming lever on the ECX housing to the bottom and the face plate slider to...

Leer más
Q:

I have verified a 120V input to my power supply and 24V output but my LIPROTEC LED still does not illuminate. What should I do?

A:

Ensure that the low voltage (+ and -) connections are correct and not reversed. The connections should be...

Leer más

Related Products

LED Shower Niches

Schluter®-KERDI-BOARD-SNLT

LED Shower Niches

Schluter®-LIPROTEC-CW