Schluter®-KERDI-SHOWER-FRS™
Sistema de rebajado del piso para duchas sin rebordes
- Los soportes de acero galvanizado proporcionan un apoyo sólido para el substrato rebajado
- Diseñado para instalaciones de ducha sin rebordes con desagües tradicionales KERDI-DRAIN
- No se modifican las vigas, lo que mantiene la integridad estructural
- Los soportes se fijan directamente a la parte superior de las vigas: no es necesario utilizar tablas de apoyo
- Compatible con vigas en I y madera dimensional con un espaciado de hasta 19.2" (488 mm) desde los centros
- Reduce la altura del substrato en 11/16" (17.5 mm)
- Compatible con una gran variedad de paneles prefabricados KERDI-SHOWER
- La fijación en la parte superior de las vigas minimiza la interferencia con la plomería, el sistema de climatización y las instalaciones eléctricas dentro de las cavidades del piso
Find recommended accessories here
Estimador de sistema de ducha
Calcule todo lo que necesita para su ducha
J Brackets fasten to the top of joists and support FRS system inserts in the recessed section of the floor.
P Brackets fasten to the unmodified subfloor at the perimeter, including along wall bottom plates, and support FRS System inserts in the recessed portion of the floor.
Shims allow 5/8” subflooring to be used with KERDI-SHOWER-FRS. Shims are applied to P Brackets to accommodate the additional thickness needed for a secure interface with 5/8” subflooring.
Schluter®-KERDI-SHOWER-FRS™ is installed in the floor under the shower assembly and requires no special maintenance or care. The systems components are resistant to mold and fungi.
For a step-by-step guide on installing the Schluter®-KERDI-SHOWER-FRS™ floor recessing system for curbless showers, visit our installation instructions.
Warranties
FAQ
What is the maximum allowable joist spacing for KERDI-SHOWER-FRS applications?
Do I have to cut into the floor joists to install KERDI-SHOWER-FRS?
No, KERDI-SHOWER-FRS is designed to recess the subfloor between the joists, eliminating...
Read moreHow many brackets do I need for my KERDI-SHOWER-FRS installation?
The number of brackets required depends on your specific installation conditions, including joist spacing, joist orientation, and...
Read moreWhat adhesives can I use on the KERDI-SHOWER-FRS brackets?
How far should waterproofing extend beyond the shower threshold in a curbless shower?
In a curbless shower, waterproofing should ideally extend across the entire bathroom floor, as it must be installed in...
Read moreDoes the orientation of the plywood inserts matter in KERDI-SHOWER-FRS applications?
Perpendicular placement is preferred, but KERDI-SHOWER-FRS plywood inserts may be installed with...
Read moreCan I use different screws with KERDI-SHOWER-FRS?
No, the screws included with KERDI-SHOWER-FRS kits have been specifically selected and thoroughly tested for...
Read moreWhy do I have leftover brackets and screws in my KERDI-SHOWER-FRS kit after installation?
KERDI-SHOWER-FRS kits were designed to provide the materials needed for most installation conditions...
Read moreCan I recess the entire floor using KERDI-SHOWER-FRS?
Can I use KERDI-SHOWER-FRS with linear drains?
Do I need to pre-drill (i.e., create pilot holes) before fastening the brackets?
No, pilot holes are not required. However, predrilling can increase the speed, ease, and...
Read moreI lost some of the screws from my KERDI-SHOWER-FRS kit, what should I do?
Watch & Learn
About the product
How to install the Schluter®-KERDI-SHOWER-FRS Floor Recessing System
Schluter®-KERDI-SHOWER-FRS Floor Recessing System for Curbless Showers
Find some existing tutorials and project documentation videos to learn how-to get the best out of our products - for more fun in your life, start now!
Watch more videos / playlists
