Schluter®-BARA-RAK

Edging profile with drip lip for balconies

Schluter®-BARA-RAK is a color-coated aluminum balcony edging profile with a drip lip. It is designed to be fitted to the edges of finished sloped surfaces to form both an edging and a drip lip.
  • Produces a clean edge finish and protects the exposed edges against weathering and decay
  • 90° inside corners, 90° and 135° outside corners, and connectors are available
  • Ideally integrated with a suitable waterproofing membrane
  • Available in stainless steel
 ...read more  ...show less

Product type

Select all options to find the
specific product you want to buy.

Find recommended accessories here

Schluter® BARA-RAK is a color coated aluminum edging profile with a drip lip.The profile finishes the exposed edges of floor assemblies on balconies and terraces that have an existing sloped screed.The trapezoid-perforated anchoring leg of Schluter®-BARA-RAK should be integrated with a suitable waterproofing membrane such as TROBA-PLUSOnce the anchoring leg of Schluter®-BARA-RAK becomes integrated with the waterproofing membrane, tile installation can begin.

When using Schluter-BARA-RAK as an edging profile for floor assemblies that are to receive a waterproofing membrane with a mortar screed on top, a drainage layer must be incorporated into the surface assembly. Schluter-BARA-RAK produces a clean edge finish and protects the exposed edges against weathering and decay.

BARA-RAK requires no special maintenance. The coated surface of the aluminum profile is colorfast and UV-resistant. Damaged surfaces shall be painted over.

1. Using a notched trowel, apply thin-set mortar to the area where BARA-RAK is to be placed. Press the perforated anchoring leg of the profile into the thin-set mortar and align.

2. When using a bituminous, flat sheet-applied, or trowel applied waterproofing membrane, the trapezoid-perforated anchoring leg of Schluter-BARA-RAK is bonded to the sloped screed at the exposed edge area with a suitable thin-set mortar. To prevent a slope reduction at the edge area, apply a gradient transition layer of thin-set mortar between the screed and the profile. The waterproofing membrane is carried over the cut-back channels in the bonding flange and bonded with a suitable adhesive. When installing the waterproofing membrane, the instructions of the manufacturer must be observed.

3. The tiles may now be installed using the thin-bed method. Schluter-SCHIENE or Schluter-RONDEC can be applied to edge the tiles at the recessed transition to the drip lip. If the SCHIENE or RONDEC will not be used, the edge of the covering assembly should be approximately flush with the drip lip of Schluter-BARA-RAK.

4. Covering assemblies installed over a waterproofing layer may consist of a drainage membrane with a load-distribution layer (e.g. mortar bed) on top, a gravel layer, or large-format pavers supported by pedestals or stilts.

5. Please note: Prefabricated corners and connectors are available for inside corners, outside corners, and butt joints. Abut the ends of Schluter-BARA-RAK, leaving an approx. 3/16" (5 mm) joint. Cover the joint with the clip-on connector.

Product Table

11202-preview
19.55 KB
BalconyProfiles_GutterSystems
898.52 KB
Pdf

Data sheets

Balcony and Terraces Data Sheet
914.76 KB
Pdf

Warranties

BalconyandTerrace-Profiles-Warranty
57.34 KB
Pdf
Q:

How do I cut profiles?

A:

Schluter™ profiles are available in a variety of different materials , so methods for cutting vary. Below are best practices for cutting according...

Read more

Spec. Guides

Product Spec Guide 2019
1.25 MB
Pdf

Specify our products using the

Specification Logo

For Walls / Edging & Outside Wall Corners

Schluter®-JOLLY