Schluter®-VINPRO-U

Resilient surface floor profile for reducing to lower elevations

Schluter®-VINPRO-U is designed to provide a smooth transition between resilient floor coverings (e.g., LVT) and floor coverings at lower elevations. The sloped surface has been designed to eliminate trip hazards while still providing a discreet and minimal reveal.
  • NEW! Now available in 11 additional sizes
  • Prevents resilient surface coverings from chipping
  • Creates smooth transitions to eliminate trip hazards
  • Ideal for transitions from LVT coverings to finished concrete
  • Certain sizes are ADA-compliant 
  • Available in anodized aluminum in three finish colors
 ...read more  ...show less

Product type

Select all options to find the
specific product you want to buy.

Find recommended accessories here

Schluter-VINPRO-U is designed to provide a smooth transition between resilient floor coverings (e.g. LVT) and floor coverings at lower elevations or finished concrete. The profile is available in anodized aluminum. VINPRO-U features a tapered anchoring leg, with unique holes spaced evenly along the length of the profile for use with fasteners. The anchoring leg can also be bonded to the substrate using adhesive such as Schluter®-KERDI-FIX. The profile features a 1/4" (6 mm) or 3/8" (10 mm) wide sloped top flange to hide the cut edge of the resilient floor covering, providing a finished look.

Schluter resilient surface covering profiles require no special maintenance or care and are resistant to mold and fungi. Clean profiles using neutral cleaning agents. For anodized aluminum, do not use abrasive or strong alkaline cleaning agents.

1. Select the profile according to resilient covering thickness. It is recommended to choose a profile height up to a 0.5 mm greater than the floor covering thickness.

2. Place the profile in its desired position and mark the edges of the profile onto the substrate.

3.a. Adhesive Installation

Apply Schluter®-KERDI-FIX or an equivalent adhesive to the backside of the anchoring leg, according to the manufacturer's installation instructions. Press the anchoring leg onto the substrate and align to the desired position. Be sure to remove any excess adhesive promptly.

3b. Fastened Installation

Align the profile in the desired position and fasten to the substrate through the holes in the anchoring leg. Recommended screw: #6 / M3.5 flat head screws, minimum length - 3/4" (19 mm). Be sure to install the fasteners so that the screw head is flush with the anchoring leg surface, preventing it from transferring through to the finished surface.

For concrete substrates: The use of anchors is recommended. First, place the profile in its desired position and mark the hole locations onto the substrate. Next, drill pilot holes at the marked locations and install the anchors according to the manufacturer's instructions. Be sure that the anchor size is suitable for the selected fastener prior to the installation.

4. A patching/leveling compound can be used to eliminate inconsistencies in the floor and anchoring leg if required. Please refer to the patching/leveling compound manufacturer's installation instructions.

5. Install resilient covering according to the manufacturer's installation instructions, with recommended edge spacing. Be sure to cut the adjacent covering accordingly to fit within the pocket of the profile.

6. When installing with adhesives or grouting materials, remove any residue from the visible surface of the profile quickly.

Brochures and Pamphlets

VINPRO Brochure
2.67 MB
Pdf
Profile Finishes and Colors
2.82 MB
Pdf

Product Table

16500-preview
15.45 KB
VINPRO
600.57 KB
Pdf

Data sheets

VINPRO Data Sheet
752.47 KB
Pdf

Warranties

VINPRO Profiles Warranty
10.13 MB
Pdf
Q:

Are screws included with the VINPRO profiles?

A:

Screws are not included with the profiles. #6 / M3.5 screws are recommended ...

Read more
Q:

Is a leveling patch required to feather out the anchoring leg to prevent telegraphing through to the top surface of the vinyl flooring?

A:

No, the anchoring leg for VINPRO is designed with this issue in mind...

Read more
Q:

What finishes are the VINPRO profiles available in?

A:

The VINPRO profiles are available in brushed chrome (ACGB), brushed nickel (ATGB), and brushed antique bronze (ABGB) ...

Read more
Q:

How can I choose the best profile height for my resilient covering?

A:

We recommend choosing the profile height that is up to a 0.5 mm greater than the coverings thickness ...

Read more

CAD drawings

VINPRO-U drawing - dessin
511.29 KB
Pdf
VINPRO-U drawing - dessin
263.86 KB
DWG

Specify our products using the

Specification Logo
Player

Watch & Learn
About the product

Schluter®-VINPRO: Profiles for resilient floor and wall coverings

Schluter®-VINPRO: Profiles for resilient floor and wall coverings

04:55

Find some existing tutorials and project documentation videos to learn how-to get the best out of our products - for more fun in your life, start now!

Watch more videos / playlists

Profiles for LVT / LVT Applications on Walls

Schluter®-VINPRO-S

Profiles for LVT / LVT Applications on Floors

Schluter®-VINPRO-T

Movement Joint Profiles / Surface & Expansion Joints

Schluter®-DILEX-EKSB

Profiles for LVT / LVT Applications on Walls

Schluter®-VINPRO-RO

Profiles for LVT / LVT Applications on Stairs

Schluter®-VINPRO-STEP

Profiles for LVT / LVT Applications on Stairs

Schluter®-VINPRO-STEP-R